Platform information
Filesystem
btrfs
cmdline
cmdline: console=ttyS2 console=ttyS2,115200 root=/dev/mmcblk0p3 rw rootwait rootfstype=btrfs
Linux version
Linux version 4.1.43-pulsar-standard (svc-pulsar@d8cd0e6db2f3) (gcc version 5.2.0 (GCC) ) #1 SMP PREEMPT Thu Jul 25 06:56:18 UTC 2019
Misc
MD90785 für Set MD90790
EAN: 4015625907852
Hardware revision: SHC2.0
Full boot log
Terminal ready
bus_id 0
bus_mfp 0
pmu_id 3
vddr_pmu_dcdc_cfg 4
ddr_clk 588
ddr_cap 1024
ddr_bits_width 0
rank 1
ddr_type 0
row_col 0
rdodt 1
wrodt 1
zpzq 12
rx_tx_adfu 1
uart_id 2
uart_baudrate 115200
uart_pad 9
jtag_pad 0
bootdev 32
version 1.1
scan 1
busid = 0bus_mfp = 0pmu_id = 3vddr_pmu_dcdc_cfg = 4
ddr_clk = 0x24c ddr_cap = 400 ddr_bits_width = 0 rank = 1 ddr_type = 0 row_col = 0 rdodt = 1 wrodt = 1 zpzq = c, row_col_detect = 68
consolse init :port 2, baudrate 115200 mfp 9
pmu init
busid = 0bus_mfp = 0pmu_id = 3vddr_pmu_dcdc_cfg = 4
g_current_bus = 00x51:0x8d1:0x8d1
0x39:0x3268:0x3268
0x14:0xaca
VERSION B:up 1.3V , set val = 0x8aca
0x14:0x8aca:0x8aca
0x62:0x200
0x15:0xe8ce:0xe8ce
0x16:0x334b:0x334b
ATC2609A_PMU_SYS_CTL3 = 17024
,s2 flag = 0
enter from s4check adfu
reg_val = 0x6c20ddr init
ddr_cap = 0 row_col = 0 row_col_detect = 0
DRAM init mode0,type0,2cs,x32,588MHz,0x0.@150616_R...Fail:0x8023,0x8023,0x8023,0x8023;0x0,0x0,0x0,0x0
DRAM init mode0,type0,1cs,x32,588MHz,0x334d.@150616_R...Ok:1024MByte Cap.
ddr size=1024MB
load app
load uboot: load address is 0x8000000, entry point is 0x8000040
in fourth
dvfs = 0xc583bb75
ddr scan = 1
dvfs maigc = 0x44564653, dvfs = 0xc583bb75ddr_clk = 0x24c ddr_cap = 400 ddr_bits_width = 0 rank = 1 ddr_type = 0 row_col = 0 rdodt = 1 wrodt = 1 zpzq = c, row_col_detect = 68
mmc->clock=187500
low rate:0x100
error: SDC2 send CMD8, No rsp
error: SDC2 send CMD55, No rsp
go to try mmc card
mmc->clock=52000000
high:0x0
boot sd/emmc init ok
mmc cap:5611520
U-Boot 2015.04 (Jul 28 2018 - 03:37:13)Actions-Semi
DRAM: mem-size=1024MB
1 GiB
PLL:core=0x332,dev=0x1164,bus=0x1c710000,bus1=0x2e004,display=0x164, spead=0x0
set kinfo addr = 3f700000
gpio=23,mode=0,val=0
gpio=25,mode=0,val=0
gpio=33,mode=0,val=0
gpio=55,mode=0,val=0
pwm_init, blob 3defc0d8
PWM init, node 4560
not find HOSC dat = 0xca
ret = 7104
owl: begin analysis pmu in device tree
node = 9732
owl: have for pmu in device tree , node =9732
pmu_config.bus_id = 0
pmu_config.dcdc_en_bm = 14
pmu_config.dcdc_cfgs[0] = 0
pmu_config.dcdc_cfgs[1] = 11
pmu_config.dcdc_cfgs[2] = 10
pmu_config.dcdc_cfgs[3] = 5
pmu_config.ldo_en_bm = 131
pmu_config.ldo_cfgs[0] = 1
pmu_config.ldo_cfgs[1] = 7
pmu_config.ldo_cfgs[2] = 0
pmu_config.ldo_cfgs[3] = 0
pmu_config.ldo_cfgs[4] = 0
pmu_config.ldo_cfgs[5] = 0
pmu_config.ldo_cfgs[6] = 0
pmu_config.ldo_cfgs[7] = 3
pmu_config.ldo_cfgs[8] = 0
pmu_config.ldo_cfgs[9] = 0
pmu_config.ldo_cfgs[10] = 0
pmu_config.ldo_cfgs[11] = 0
pmu_type = 2
pmu_config.pwm_config[0].pwm_val = 0x0
pmu_config.pwm_config[0].mfp.shift = 0
pmu_config.pwm_config[0].mfp.mask = 0
,pmu_config.pwm_config[0].mfp.val = 0
pmu_config.pwm_config[0].mfp.no = 0
pmu_config.pwm_config[1].pwm_val = 0x102c3f
pmu_config.pwm_config[1].mfp.shift = 38
pmu_config.pwm_config[1].mfp.mask = 7
,pmu_config.pwm_config[1].mfp.val = 3
pmu_config.pwm_config[1].mfp.no = 1
pmu_config.pwm_config[2].pwm_val = 0x10343f
pmu_config.pwm_config[2].mfp.shift = 38
pmu_config.pwm_config[2].mfp.mask = 7
,pmu_config.pwm_config[2].mfp.val = 3
pmu_config.pwm_config[2].mfp.no = 1
pwm1 val=0x102c3f
pwm2 val=0x10343f
0x51:0x8d1:0x8d1
0x39:0x3268:0x3268
0x11:0xe5cf:0xe5cf
0x12:0x68cc:0x68cc
0x13:0x334b:0x334b
0x17:0x8aaa:0x8aaa
0x18:0xe14c:0xe14c
0x19:0x338a:0x338a
pmu init finish!
begin to check power!
wall_mv=5061
----------the plug_stat is 0-NO_PLUG,1-WALL_PLUG,2-USB_PLUG:1
----------bat_voltage = 609
bat_mv:609
node_path[2]=/i2c@b0170000/atc2603c@65/atc260x-power
support type: both DCIN and USB
low_power_boot_choice is 0
support_minicharger:1
MMC: error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
slot:0, error mmc_init
error:-1,owl_sd_init fail
error: SDC2 send CMD8, No rsp
error: SDC2 send CMD55, No rsp
SD0: 0, eMMC: 1 (eMMC)
Using default environment
bootmode = 0
emmc boot
** get_partition_info mmc1:6
** Partition 6 not valid on device 1 **
error: SDC0 send CMD8, No rsp
error: SDC0 send CMD55, No rsp
error: SDC0 send CMD1, No rsp
Card did not respond to voltage select!
Failed to find mmc:0
bootlogo: if=mmc, dev=1
reading boot_logo.bmp.gz
Fail to load splash image
reading new_gamma_data
Fail to load gamma
OWL VIDEO: video hw init
OWL VIDEO: power on
OWL VIDEO: wait res 998, 113301
OWL LCD: lcd init
fdtdec_get_lcd_par
Can't get lcd mode node
OWL LCD: fdt No lcd par
OWL dsi: dsi init
buf->vaddr 0x3df01450 buf->paddr 0x3df01450
fdtdec_get_dsi_par0
Can't get dsi mode node
OWL dsi: fdt No dsi par
fdtdec_get_hdmi_par
fdtdec_get_hdmi_par: resolution = auto
fdtdec_get_hdmi_par: not support auto ,we used default vid = 1039116848
cvbs_init uboot
fdtdec_get_cvbs_par: resolution = PAL
boot cvbs vid =0
cvbs boot init
def_display_name hdmi
def_display_name hdmi not found
bpp 4
get fb dss, img_w = 1280
get fb dss, img_h = 720
In: serial
Out: serial
Err: serial
HW info magic facedead
HW info 401562590785213494, 01.00a
reading owl_boot_flag
** Unable to read file owl_boot_flag **
reading owl_boot_backup
Net: owl_mac_parse_fdtdec,phy_addr 3
owl_mac_parse_fdtdec,power-gpio -1
owl_mac_parse_fdtdec,reset-gpio 88
owl_mac
Warning: owl_mac using MAC address from net device
Update MAC: 20:50:6c:65:61:73
, usb_ether
Error: usb_ether address not set.
Enter s500 to abort autoboot in 2 seconds
Start stage 1 checking -------------
writing owl_boot_flag
OWL VDE: power on
OWL VDE: wait res 999, 113301
enabling watchdog timeout=60s
change watchdog timeout from 60ls to 120ls
boot from emmc card ...
reading uEnv.txt
297 bytes read in 4 ms (72.3 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
reading fitImage
14538310 bytes read in 620 ms (22.4 MiB/s)
## Loading kernel from FIT Image at 04100000 ...
Using 'conf@actduino_bubble_gum_sdboot_linux.dtb' configuration
Verifying Hash Integrity ... sha1,rsa2048:dev+ OK
Trying 'kernel@1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x04100108
Data Size: 5879104 Bytes = 5.6 MiB
Architecture: ARM
OS: Linux
Load Address: 0x01314c40
Entry Point: 0x01314c40
Hash algo: sha1
Hash value: 1c660b57e62239013b84e1bef6d8e6680da113cd
Sign algo: sha1,rsa2048:dev
Sign value: 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
Verifying Hash Integrity ... sha1+ sha1,rsa2048:dev+ OK
## Loading ramdisk from FIT Image at 04100000 ...
Using 'conf@actduino_bubble_gum_sdboot_linux.dtb' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: cube-builder-initramfs
Type: RAMDisk Image
Compression: gzip compressed
Data Start: 0x046a41fc
Data Size: 8621214 Bytes = 8.2 MiB
Architecture: ARM
OS: Linux
Load Address: unavailable
Entry Point: unavailable
Hash algo: sha1
Hash value: 3ef3e4cbafd6cbc1cbe3b11bcef7df68c39db68c
Sign algo: sha1,rsa2048:dev
Sign value: 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
Verifying Hash Integrity ... sha1+ sha1,rsa2048:dev+ OK
## Loading fdt from FIT Image at 04100000 ...
Using 'conf@actduino_bubble_gum_sdboot_linux.dtb' configuration
Trying 'fdt@actduino_bubble_gum_sdboot_linux.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x0469b8e4
Data Size: 34513 Bytes = 33.7 KiB
Architecture: ARM
Hash algo: sha1
Hash value: 4d3016d23cb25422cc56a3f799d124b3ee2f48e3
Sign algo: sha1,rsa2048:dev
Sign value: 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
Verifying Hash Integrity ... sha1+ sha1,rsa2048:dev+ OK
Booting using the fdt blob at 0x469b8e4
Loading Kernel Image ... OK
Using Device Tree in place at 0469b8e4, end 046a6fb4
owl_boot_fdt_setup linux
read_mi_head, line 429, magic 0x0, length 0, item num 0
read Head null
read SN failed
cmdline: console=ttyS2 console=ttyS2,115200 root=/dev/mmcblk0p3 rw rootwait rootfstype=btrfs usbcore.autosuspend=-1 boot_dev=sd2
Starting kernel ...
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 4.1.43-pulsar-standard (svc-pulsar@d8cd0e6db2f3) (gcc version 5.2.0 (GCC) ) #1 SMP PREEMPT Thu Jul 25 06:56:18 UTC 2019
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Actions GS705A board
owl_reserve: pyhsical memory size 1073741824 bytes, end @0x2f800000
find owl_fb_size=0x800000
find owl_kinfo_size=0x100000
Reserved memory 0MB
FB: 0x2f000000, 8MB
KINFO: 0x2ef00000, 1MB
ION0: 0x00000000, 0MB
ION1: 0x00000000, 0MB
cma: Reserved 48 MiB at 0x3d000000
Memory policy: Data cache writealloc
owl_smp_init_cpus(): ncores 4
PERCPU: Embedded 13 pages/cpu @ee5a8000 s21952 r8192 d23104 u53248
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260434
Kernel command line: console=ttyS2 console=ttyS2,115200 root=/dev/mmcblk0p3 rw rootwait rootfstype=btrfs usbcore.autosuspend=-1 boot_dev=sd2
boot_mode_process
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 957168K/1048576K available (9164K kernel code, 703K rwdata, 2352K rodata, 576K init, 1405K bss, 42256K reserved, 49152K cma-reserved, 221184K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0b474d8 (11518 kB)
.init : 0xc0b48000 - 0xc0bd8000 ( 576 kB)
.data : 0xc0bd8000 - 0xc0c87d5c ( 704 kB)
.bss : 0xc0c87d5c - 0xc0de7278 (1406 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
Additional per-CPU info printed with stalls.
NR_IRQS:247
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
clocksource timer0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
Console: colour dummy device 80x30
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys debug
CPU: Testing write buffer coherency: ok
CPU0: Spectre v2: using BPIALL workaround
ftrace: allocating 31062 entries in 92 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
owl_smp_prepare_cpus(max_cpus:4)
Setting up static identity map for 0x8280 - 0x8340
owl_l2x0_init()
L2C: platform modifies aux control register: 0x32050000 -> 0x3e050000
L2C: DT/platform modifies aux control register: 0x32050000 -> 0x3e050000
L2C: DT/platform tries to modify or specify cache size
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 3 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 16 ways, 512 kB
L2C-310: CACHE_ID 0x410080c9, AUX_CTRL 0x7e050001
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU1: Spectre v2: using BPIALL workaround
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU2: Spectre v2: using BPIALL workaround
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
CPU3: Spectre v2: using BPIALL workaround
Brought up 4 CPUs
SMP: Total of 4 processors activated (4787.40 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 1024 (order: 4, 65536 bytes)
xor: measuring software checksum speed
arm4regs : 927.600 MB/sec
8regs : 703.200 MB/sec
32regs : 744.000 MB/sec
xor: using function: arm4regs (927.600 MB/sec)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 14336 KiB pool for atomic coherent allocations
init sirqs
owl_gpio_init()
cpuidle: using governor ladder
cpuidle: using governor menu
owl_gpio_probe()
owl gpio bank0 - irq18
owl gpio bank1 - irq19
owl gpio bank2 - irq20
owl gpio bank3 - irq21
owl gpio bank4 - irq22
owl_sirq_probe()
owl sirq bank0 - irq155
owl sirq bank1 - irq156
owl sirq bank2 - irq157
sirq map 155 -> 158
sirq map 156 -> 159
sirq map 157 -> 160
owl_board_init()
hw-breakpoint: Debug register access (0xee114e91) caused undefined instruction on CPU 0
hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 1
hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 3
hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 2
hw-breakpoint: CPU 3 debug is powered down!
hw-breakpoint: Debug register access (0xee113e95) caused undefined instruction on CPU 0
free reserve pages 256 to buddy system
owl_common_init()
[PowerGate] name: 'dma', on: 0, before SPS_PG_CTL: 0x703360
[PowerGate] name: 'dma', on: 0, after SPS_PG_CTL: 0x703260
dmm debugfs support
i2c i2c-2: of_i2c: invalid reg on /i2c@b0178000/mpu6515@68
raid6: int32x1 gen() 87 MB/s
raid6: int32x1 xor() 99 MB/s
raid6: int32x2 gen() 106 MB/s
raid6: int32x2 xor() 96 MB/s
raid6: int32x4 gen() 108 MB/s
raid6: int32x4 xor() 84 MB/s
raid6: int32x8 gen() 106 MB/s
raid6: int32x8 xor() 76 MB/s
raid6: using algorithm int32x4 gen() 108 MB/s
raid6: .... xor() 84 MB/s, rmw enabled
raid6: using intx1 recovery algorithm
pwm-owl b01b0050.pwm: Probing...
owl_dma_init
owl_dma_probe
[PowerGate] name: 'dma', on: 1, before SPS_PG_CTL: 0x702260
[PowerGate] name: 'dma', on: 1, after SPS_PG_CTL: 0x703360
owl_dma b0260000.dma: actions AHB DMA Controller ( cpy slave ), 12 channels
atc260x_i2c 0-0065: Probing...
atc260x_i2c 0-0065: atc260x_core_dev_init() enter
atc260x_i2c 0-0065: set bdg ctl, ret=0 value=0xd1
atc260x_i2c 0-0065: detect PMU chip type 1 ver B
atc260x_i2c 0-0065: PMU root IRQ 160
atc260x_i2c 0-0065: icm_ohm not config, use default value
atc260x_i2c 0-0065: auxadc icm_ohm = 20
atc260x-regulator atc2603c-dcdc1.1: Probing atc2603c-dcdc1, id=1
atc260x-regulator atc2603c-dcdc2.2: Probing atc2603c-dcdc2, id=2
atc260x-regulator atc2603c-dcdc3.3: Probing atc2603c-dcdc3, id=3
atc260x-regulator atc2603c-ldo1.1: Probing atc2603c-ldo1, id=1
atc260x-regulator atc2603c-ldo2.2: Probing atc2603c-ldo2, id=2
atc260x-regulator atc2603c-ldo3.3: Probing atc2603c-ldo3, id=3
atc260x-regulator atc2603c-ldo5.5: Probing atc2603c-ldo5, id=5
atc260x-regulator atc2603c-ldo6.6: Probing atc2603c-ldo6, id=6
atc260x-regulator atc2603c-ldo7.7: Probing atc2603c-ldo7, id=7
atc260x-regulator atc2603c-ldo8.8: Probing atc2603c-ldo8, id=8
atc260x-regulator atc2603c-ldo11.11: Probing atc2603c-ldo11, id=11
atc260x-switch-ldo atc2603c-switch1.1: Probing atc2603c-switch1, id=1
atc260x-switch-ldo atc2603c-switch1.1: pmic_ver=1
[SWITCH1] set switch 1 to ldo mode Version D!
atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc1.1: Probing atc2603c-ext-pwm-dcdc1
atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc1.1: table_len = 15
atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc1.1: got init voltage selector 8
atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc2.2: Probing atc2603c-ext-pwm-dcdc2
atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc2.2: table_len = 15
atc260x-ext-pwm-dcdc atc2603c-ext-pwm-dcdc2.2: got init voltage selector 6
atc260x_i2c 0-0065: atc260x_core_dev_init() exit
atc260x-pm atc2603c-pm.0: Probing...
atc260x-pm atc2603c-pm.0: _set_s2_mode() can not get of_property s2_mode
atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() enter, mask=0x7fff src=0x706
atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() setup reg=0x0 msk=0xffe0 val=0xe0c0 readback=0xe0cb
atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() setup reg=0x3 msk=0xc val=0x0 readback=0x4280
atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() enter, mask=0x8 src=0x0
atc260x-pm atc2603c-pm.0: _atc260x_pm_set_wakeup_src_inner() setup reg=0x0 msk=0x100 val=0x0 readback=0xe0cb
atc260x-pm atc2603c-pm.0: _clear_status() no need to restore old alarm
atc260x-pm atc2603c-pm.0: got support_adaptor_type: 3
atc260x-pm atc2603c-pm.0: translated wakeup falgs: 0x200
[PM] set pmic suspend ops 0xc0c50904
atc260x-pm atc2603c-pm.0: #####atc260x_pm_probe PMU_SYS_CTL0:0xe0cb ####
SCSI subsystem initialized
asoc_spi0 b0200000.spi: master is unqueued, this is deprecated
asoc_spi0 b0208000.spi: master is unqueued, this is deprecated
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.20
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switched to clocksource timer0
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 8420K (c46a4000 - c4edd000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
owl_uart: no device is found
b0120000.serial: ttyS0 at MMIO 0xb0120000 (irq = 9, base_baud = 0) is a OWL_SERIAL
b0124000.serial: ttyS2 at MMIO 0xb0124000 (irq = 10, base_baud = 0) is a OWL_SERIAL
console [ttyS2] enabled
b0126000.serial: ttyS3 at MMIO 0xb0126000 (irq = 11, base_baud = 0) is a OWL_SERIAL
## boot_dev: 0x22
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
aufs 4.1-20150629
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
owl_dss DE: owl_de_probe, pdev = 0xee27bc00
owl_dss DE: DE INITED FROM UBOOT ?? 0
owl_dss DE: de parent pll is 600000000hz
owl_dss DE: de irq init ok
owl_dss MMU: mmu_init: base 0xf0f07000 base_phys 0xc0842f483de00000 free_info->addr 0xf0f07000
generic_dsi_panel_drv_init
tpm_tis_spi spi2.0: 1.2 TPM (device-id 0x0, rev-id 78)
tpm tpm0: Issuing TPM_STARTUP
brd: module loaded
loop: module loaded
misc_info_init, line 1075
mi_debug_init, line 372
atc260x-pwm atc2603c-pwm.0: atc260x_pwm Probing...
atc260x_pwm_drv: [atc260x_pwm_on start]
atc260x_pwm_drv: [atc260x_pwm_on finished]
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
asoc_ethernet_init 3632
no blk dev
read MiscInfoHeader failed
read Head failed
random-mac-address: disabled
local-mac-address:
phy_mode: 0
target freq: 50000000
asoc_ethernet_probe can't get phy power gpio
compatible of /ethernet@b0310000/ethernet-phy@0: realtk,rtl8201
phy model: RTL8201
net device : eth0 init over.
ethernet eth0 probe finish
usbcore: registered new interface driver r8152
port_host_plug_detect[0]:1
port0_vubs_en:36
port_host_plug_detect[1]:1
port1_vubs_en:36
can't find aotg_udc_enable config
can't find aotg_udc_enable config
No aotg_udc being enabled!
------------dwc3_clk_init-----ic=1-----
[PowerGate] name: 'usb3', on: 1, before SPS_PG_CTL: 0x703360
[PowerGate] name: 'usb3', on: 1, after SPS_PG_CTL: 0x707760
GS705A phy init for dwc3 gadget
GS705A phy init for dwc3 gadget
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver cp210x
usbserial: USB Serial support registered for cp210x
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
mousedev: PS/2 mouse device common for all mice
atc260x-onoff atc2603c-onoff.0: Probing atc2603c-onoff
atc260x-onoff atc2603c-onoff.0: atc260x_onoff IRQ num : 174
input: atc260x_onoff as /devices/platform/b0170000.i2c/i2c-0/0-0065/atc2603c-onoff.0/input/input0
atc260x-rtc atc2603c-rtc.0: Probing...
atc260x-rtc atc2603c-rtc.0: rtc core: registered atc260x-RTC as rtc0
atc260x-rtc atc2603c-rtc.0: RTC alarm IRQ num : 175
i2c /dev entries driver
thermal thermal_zone0: failed to read out thermal zone (-19)
ATC260X_POWER: create sysfs for atc260x power
charger=ee2f3010 2717
set_vbus_path=c0585668 set_apds_vbus_pd=c05857a8
ATC260X_GAUGE: ========This is a new reconstructed gauge by actions==========
ATC260X_GAUGE: [atc260x_gauge_init] drv name:atc260x-cap-gauge, drv version:Actions-v1-20150720151405
ATC260X_GAUGE: [gauge_create_sysfs] create sysfs for gauge
ATC260X_GAUGE: [get_pmu_ic_type]pmu type is 1
ATC260X_GAUGE: [init_gauge] PMU current ratio:3
ATC260X_GAUGE: [init_gauge] first_product:0
ATC260X_GAUGE: [resistor_init] inited ch_resistor : 150, inited disch_resistor:250
atc260x-hwmon atc2603c-hwmon.0: Probing atc2603c-hwmon
tmu-mem:start=0xb01b00e8
owl_wdt b0020600.twd-watchdog: watchdog soft mode
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: multipath personality registered for level -4
md: faulty personality registered for level -5
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.31.0-ioctl (2015-3-12) initialised: [email protected]
Bluetooth: HCI UART driver ver 2.3
Bluetooth: HCI UART protocol H4 registered
Bluetooth: HCI UART protocol Three-wire (H5) registered
## host_id: 0 boot_dev 22 host->index: 1
gl520x_mmc b0230000.mmc: using dma0chan4 for DMA transfers
use GPIO to detect SD/MMC card
owl pinctrl: gpio_request_check_pinmux
owl pinctrl: CHECK PMX:P_UART2_CTSB has already been requested by b0124000.serialhost0: sure rescan mmc
## host_id: 1 boot_dev 22 host->index: 2
gl520x_mmc b0234000.mmc: using dma0chan5 for DMA transfers
owl pinctrl: gpio_request_check_pinmux
owl pinctrl: CHECK PMX:P_UART2_RTSB has already been requested by b0124000.serialhost1: sure rescan mmc
## host_id: 2 boot_dev 22 host->index: 0
gl520x_mmc b0238000.mmc: using dma0chan6 for DMA transfers
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using arm/armv7-ca9
u32 classifier
Actions configured
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Key type dns_resolver registered
Registering SWP/SWPB emulation handler
[PM] owl_pm_init() 1019
train_Msize:1024, train_ces:1
start:0xc0008000, end:0xc0b474d8, checksum:0xeb732b36
Btrfs loaded
#### insmod vde driver!
mali0 b0280000.vde: Probe vde device
info ic_type 0x5206
vde->irq =a7
cputherm_register_notifier list 0
vde : notify_pre: vde_limit_notify: wrong vde clk value, and NOTIFY_BAD
vde : notify_abort: ABORT_RATE_CHANGE: rate: [600000000, 300000000]
[power] No battery detected
mali0 b0280000.vde: resource: iomem: [mem 0xb0280000-0xb0280107] mapping to f8280000, irq 167
host2,platfrom request already
sps base = 0xf81b0100
cmu base = 0xf8160000
SPS_PG_CTL = 0xf81b0100
Share_Mem_REG = 0xf8240004
CMU_COREPLL = 0xf8160000
CMU_VDE_CLK = 0xf8160040
CMU_DEVRST0 = 0xf81600a8
CMU_DEVCLKEN0 = 0xf81600a0
device_create_file !
fbdev info : xres 720 yres 576 refresh 24 name cvbs
fb_infos allocated
[atc260x_bat_get_props] first_power_on = false!
mmc0: MAN_BKOPS_EN bit is not set
mmc_add_card: bootdev 0x22
force sd2(emmc) host emmc_boot_card
mmc0: new high speed MMC card at address 0001
## md->name_idx: 0
mmcblk0: emmc_boot_card DG4016 14.7 GiB
mmcblk0: p1 p2 p3 p4
set_par(0)
Console: switching to colour frame buffer device 90x36
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
upgrade process hdmi disabled!!
np ee5f1668
boot_hdmi_rotate 0
boot_cvbs_enable 1
boot_hdmi_rotate 0 boot_cvbs_rotate=0
console [netcon0] enabled
netconsole: network logging started
atc260x-rtc atc2603c-rtc.0: setting system clock to 2023-09-25 11:27:32 UTC (1695641252)
fdt: not creating '/sys/firmware/fdt': CRC check failed
====otgvbus_gpio: num-37, active-high---detect_type=3,idpin_type=0,vbus_type=2---
cfg80211: Calling CRDA to update world regulatory domain
ALSA device list:
No soundcards found.
Freeing unused kernel memory: 576K (c0b48000 - c0bd8000)
starting version 225
random: udevd urandom read with 6 bits of entropy available
mdadm: looking for devices for further assembly
mdadm: no recogniseable superblock on /dev/mmcblk0p4
mdadm: no recogniseable superblock on /dev/mmcblk0p3
mdadm: no recogniseable superblock on /dev/mmcblk0p2
mdadm: Cannot assemble mbr metadata on /dev/mmcblk0p1
mdadm: Cannot assemble mbr metadata on /dev/mmcblk0
mdadm: no recogniseable superblock on /dev/ram15
mdadm: no recogniseable superblock on /dev/ram14
mdadm: no recogniseable superblock on /dev/ram13
mdadm: no recogniseable superblock on /dev/ram12
mdadm: no recogniseable superblock on /dev/ram11
mdadm: no recogniseable superblock on /dev/ram10
mdadm: no recogniseable superblock on /dev/ram9
mdadm: no recogniseable superblock on /dev/ram8
mdadm: no recogniseable superblock on /dev/ram7
mdadm: no recogniseable superblock on /dev/ram6
mdadm: no recogniseable superblock on /dev/ram5
mdadm: no recogniseable superblock on /dev/ram4
mdadm: no recogniseable superblock on /dev/ram3
mdadm: no recogniseable superblock on /dev/ram2
mdadm: no recogniseable superblock on /dev/ram1
mdadm: no recogniseable superblock on /dev/ram0
mdadm: No arrays found in config file or automatically
Option -q no longer supported.
========usb_detect_plugout_event===start det!!========
----udc_set_plugstate--PLUGSTATE_OUT--
[PowerGate] name: 'usb3', on: 0, before SPS_PG_CTL: 0x717761
[PowerGate] name: 'usb3', on: 0, after SPS_PG_CTL: 0x717361
++++++++cpufreq ready++++++++
++++++++pdata->freq_tab[0].freq_clip_max:504000++++++++
++++++++pdata->freq_tab[1].freq_clip_max:504000++++++++
------------dwc3_clk_exit----------
OWL: Kernel Thermal management registered
link status is: false
eth0 link off.
IRQ 32 requested
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Generating key, this may take a while...
BTRFS: device label OVERCROOTFS devid 1 transid 1289101 /dev/mmcblk0p3
BTRFS: device label OVERCCN devid 1 transid 2896162 /dev/mmcblk0p4
----udc_set_plugstate--PLUGSTATE_IN-2--
------------dwc3_clk_init-----ic=1-----
[PowerGate] name: 'usb3', on: 1, before SPS_PG_CTL: 0x713361
[PowerGate] name: 'usb3', on: 1, after SPS_PG_CTL: 0x717761
GS705A phy init for dwc3 gadget
GS705A phy init for dwc3 gadget
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
GS705A phy init for xhci
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f064 hci version 0x100 quirks 0x00010010
xhci-hcd xhci-hcd.0.auto: irq 165, io mem 0xb0400000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: xHCI Host Controller
usb usb1: Manufacturer: Linux 4.1.43-pulsar-standard xhci-hcd
usb usb1: SerialNumber: xhci-hcd.0.auto
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
#xhci_start#
ss_try_next_mode:lfps_src_mode=1
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.1.43-pulsar-standard xhci-hcd
usb usb2: SerialNumber: xhci-hcd.0.auto
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
----monitor_wake_lock for 10s
Input password:
link established.
ethernet link state:linked
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: Calling CRDA to update world regulatory domain
[PowerGate] name: 'usb2_0', on: 1, before SPS_PG_CTL: 0x717761
[PowerGate] name: 'usb2_0', on: 1, after SPS_PG_CTL: 0x71ff61
start mon 0 ......
[PowerGate] name: 'usb2_1', on: 1, before SPS_PG_CTL: 0x71ff61
[PowerGate] name: 'usb2_1', on: 1, after SPS_PG_CTL: 0x75ff65
start mon 1 ......
cfg80211: Calling CRDA to update world regulatory domain
[PowerGate] name: 'usb2_1', on: 0, before SPS_PG_CTL: 0x75ff65
[PowerGate] name: 'usb2_1', on: 0, after SPS_PG_CTL: 0x75ff61
res_mem->start--end = 0xb0700000--0xb0700fff
aotg_hcd aotg_hcd.1: pdev->id probe:1
[PowerGate] name: 'usb2_1', on: 1, before SPS_PG_CTL: 0x71ff61
[PowerGate] name: 'usb2_1', on: 1, after SPS_PG_CTL: 0x75ff65
usb reset OK: 0.
aotg_hcd aotg_hcd.1: AOTG USB Host Controller Driver
aotg_hcd aotg_hcd.1: new USB bus registered, assigned bus number 3
aotg_hcd aotg_hcd.1: irq 180, io mem 0xb0700000
aotg_hcd aotg_hcd.1: <HCD> start
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: AOTG USB Host Controller Driver
usb usb3: Manufacturer: Linux 4.1.43-pulsar-standard aotg_hub_hcd
usb usb3: SerialNumber: aotg_hcd.1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
USBEIEN(0xf299e50b): 0x80
aotg_hcd aotg_hcd.1: hcd controller initialized. OTGIRQ: 0x00, OTGSTATE: 0x02
USBEIRQ(0xf299e50a): 0x00
port_no:1 OTG IRQ, OTGSTATE: 0x03, USBIRQ:0x00
aotg_hcd aotg_hcd.1: <USB> aotg_hcd.1 connection changed: 1, acthcd->inserted: 1
aotg_hub_hotplug_timer:1746, dbg!
usb 3-1: new high-speed USB device number 2 using aotg_hcd
aotg_hcd aotg_hcd.1: device addr : 0x00000000
aotg_hcd aotg_hcd.1: <EP DISABLE> ep0 index 0 from ep [in]
aotg_hcd aotg_hcd.1: device addr : 0x00000002
usb 3-1: New USB device found, idVendor=05e3, idProduct=0610
usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 3-1: Product: USB2.0 Hub
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: Calling CRDA to update world regulatory domain
/usr/sbin/bootlogin.sh: line 3: 150 Alarm clock /usr/sbin/initramfs_login
Continue boot
Waiting for root device to be ready...
BTRFS info (device mmcblk0p3): disk space caching is enabled
BTRFS: detected SSD devices, enabling SSD mode
mount: /proc moved to /rootfs/proc.
mount: /sys moved to /rootfs/sys.
mount: /dev moved to /rootfs/dev.
switch_root /rootfs /sbin/init console=ttyS2 console=ttyS2,115200 root=/dev/mmcblk0p3 rw rootwait rootfstype=btrfs usbcore.autosuspend=-1 boot_dev=sd2
switch_root: failed to mount moving /run to /rootfs/run: Invalid argument
switch_root: forcing unmount of /run
Welcome to Pulsar Linux 8.0.0.17!
[ OK ] Reached target Remote File Systems.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Started Daily SmartPM update daemon.
[ OK ] Created slice Root Slice.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on networkd rtnetlink socket.
[FAILED] Failed to listen on Syslog Socket.
See 'systemctl status syslog.socket' for details.
[ OK ] Listening on udev Control Socket.
[ OK ] Created slice User and Session Slice.
[ OK ] Created slice System Slice.
[ OK ] Created slice system-getty.slice.
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ OK ] Listening on Journal Socket.
Mounting Debug File System...
Starting Remount Root and Kernel File Systems...
BTRFS info (device mmcblk0p3): disk space caching is enabled
Starting (null)...
Mounting Temporary Directory...
Starting Setup Virtual Console...
Starting Create list of required st... nodes for the current kernel...
Starting Load Kernel Modules...
Mounting POSIX Message Queue File Systemopenvswitch: Open vSwitch switching datapath
...
softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
Starting Journal Service...
[ OK ] Listening on udev Kernel Socket.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Reached target Slices.
systemd-journald[244]: [/etc/systemd/journald.conf:42] Unknown lvalue 'SystemMaxFiles' in section 'Journal'
[ OK ] Mounted Debug File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Temporary Directory.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Started (null).
[ OK ] Started Setup Virtual Console.
[ OK ] Started Create list of required sta...ce nodes for thesystemd-journald[244]: File /var/log/journal/cdec123738914b30a3292558a7c0571e/system.journal corrupted or uncleanly shut down, renaming and replacing.
current kernel.
[ OK ] Started Load Kernel Modules.
Mounting Configuration File System...
Starting Apply Kernel Variables...
Starting Load/Save Random Seed...
Starting udev Coldplug all Devices...
Starting Create Static Device Nodes in /dev...
[ OK ] Mounted Configuration File System.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Started Journal Service.
Starting Flush Journal to Persistent Storage...
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Found device /dev/disk/by-label/OVERCCN.
Starting File System Check on /dev/disk/by-label/OVERCCN...
[ OK ] Found device /dev/disk/by-label/SWAP.
[ OK ] Found device /dev/disk/by-label/OVERCBOOT.
Starting File System Check on /dev/disk/by-label/OVERCBOOT...
Activating swap /dev/disk/by-label/SWAP...
Adding 262140k swap on /dev/mmcblk0p2. Priority:-1 extents:1 across:262140k SS
[ OK ] Activated swap /dev/disk/by-label/SWAP.
[ OK ] Reached target Swap.
[ OK ] Started File System Check on /dev/disk/by-label/OVERCCN.
Mounting /var/lib/lxc...
[ OK ] Started File System Check on /dev/disk/by-label/OVERCBOOT.
cfg80211: Calling CRDA to update world regulatory domain
Mounting /boot...
[ OK ] Mounted /var/lib/lxc.
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
Starting Create Volatile Files and Directories...
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Open vSwitch Internal Unit...
Starting Permit User Sessions...
Starting Perform boot failure detection & rollback operations...
Starting Cube command server...
Starting Power off monitor...
[ATC260x] reg [0x0002] <- 0x1a82
Starting load marvell sd8977 modules...
act_sdio_dev: module license 'unspecified' taints kernel.
Starting D-Bus System Message Bus...
Disabling lock debugging due to kernel taint
Starting TPM 1.2 Initialization...
Starting Ethernet Bridge Filtering Tables...
Starting Login Service...
[ OK ] Started Permit User Sessions.
[ OK ] Started Power off monitor.
[ OK ] Started Ethernet Bridge Filtering Tables.
[ OK ] Started D-Bus System Message Bus.
Starting Network Service...
[ OK ] Started Login Service.
[ OK ] Started Network Service.
[ OK ] Reached target Network.
Starting /etc/rc.local Compatibility...
Starting Xinetd A Powerful Replacement For Inetd...
Starting Network Name Resolution...
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started Xinetd A Powerful Replacement For Inetd.
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
[ OK ] Started Network Name Resolution.
[ OK ] Started Cube command server.
[ OK ] Started Setup dnsmasq.
[ OK ] Started TPM 1.2 Initialization.
[ OK ] Started Perform boot failure detection & rollback operations.
[ OK ] Created slice system-systemd\x2drfkill.slice.
Starting Load/Save RF Kill Switch Status of rfkill0...
[ OK ] Started load marvell sd8977 modules.
[ OK ] Started Load/Save RF KBT FW is active(0)
ill Switch StatuBT: FW already downloaded!
s of rfkill0.
[ OK ] Reached target Bluetooth.
[ OK ] Started Open vSwitch Internal Unit.
Starting Open vSwitch...
Starting OverC puppet system configuration...
[ OK ] Started Open vSwitch.
[ OK ] Started OverC puppet system configuration.
Starting LXC Container Initialization and Autoboot Code...
[ OK ] Started LXC Container Initialization and Autoboot Code.
[ OK ] Reached target Multi-User System.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Started Update UTMP about System Runlevel Changes.
Pin out
TTL Voltage is 3.3v - make sure to pick an appropriate FTDI.
